Membuat VLAN dengan 2 Switch dan Trunk Link

 

vlan-2-switch-trunk

Konfigurasi Switch Pertama dan Kedua sama

Switch>
Switch>en
Switch#
Switch#config t
Switch(config)#

Switch(config)#vlan 2
Switch(config-vlan)#name Manajer
Switch(config-vlan)#vlan 3
Switch(config-vlan)#name Supervisor
Switch(config-vlan)#vlan 4
Switch(config-vlan)#name Leader
Switch(config-vlan)#vlan 9
Switch(config-vlan)#name native9
Switch(config-vlan)#
Switch(config-vlan)#
Switch(config-vlan)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#sh vlan brief

VLAN Name Status Ports
—- ——————————– ——— ——————————-
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
2 Manager active
3 Supervisor active
4 Leader active
9 native9 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Switch#
Switch#
Switch#
Switch#
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#
Switch(config)#
Switch(config)#int fa0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 2
Switch(config-if)#
Switch(config-if)#int fa0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 3
Switch(config-if)#
Switch(config-if)#int fa0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 4
Switch(config-if)#
Switch(config-if)#
Switch(config-if)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#sh vlan brief

VLAN Name Status Ports
—- ——————————– ——— ——————————-
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24
2 Manager active Fa0/1
3 Supervisor active Fa0/2
4 Leader active Fa0/3
9 native9 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Switch#
Switch#

Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#
Switch(config)#int fa0/4
Switch(config-if)#switchport mode trunk

Switch(config-if)#
Switch(config-if)#switchport trunk native vlan 9
Switch(config-if)#
Switch(config-if)#
%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet0/4 (9), with Switch FastEthernet0/4 (1).

%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet0/4 (9), with Switch FastEthernet0/4 (1).
Switch(config-if)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#
Switch#
Switch#sh vlan brief

VLAN Name Status Ports
—- ——————————– ——— ——————————-
1 default active Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
2 Manager active Fa0/1
3 Supervisor active Fa0/2
4 Leader active Fa0/3
9 native9 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
Switch#
Switch#

LEAVE A REPLY